[Helpful] The Most Effective 200-355 Dumps Exam Video Certification Covers All Key Points

What is the best way to pass the Cisco 200-355 dumps? "Implementing Cisco Wireless Network Fundamentals", also known as 200-355 dumps, is a Cisco Certification. With the complete collection of questions and answers, Pass4itssure has assembled to take you through 378 Q&As to your 200-355 exam preparation.

Student for any Cisco https://www.pass4itsure.com/200-355.html dumps is usually a difficult task but you certainly want to ensure that you have adequate MicrosoftCisco 200-355 dumps study materials at your clearance.

Exam Code: 200-355
Exam Name: Implementing Cisco Wireless Network Fundamentals
Updated: Sep 11, 2017
Q&As: 378  

Cisco 200-355 Dumps From Google Drive: https://drive.google.com/open?id=0BwxjZr-ZDwwWUkUwT0lYclNxbFU
Microsoft 70-486 Dumps From Google Drive: https://drive.google.com/open?id=0BwxjZr-ZDwwWSG9tSWFYaFZMREE

QUESTION 17:
The segment-to-device mapping is maintained by
A. the master database's sysdevices table
B. the local database's syssegments table
C. the master database's syssegments table
D. the local database's sysindexes.segment column
E. the master database's sysusages.segmap column
200-355 exam Answer: E
QUESTION 18:
A transaction log (choose two)
A. is a separate entity from the database
B. can be broken down into sections: redo and undo
C. is the system table syslogs
D. exists once for the whole ASE
E. is on the segment logsegment
Answer: CE
QUESTION NO: 19
You are at the system level. Which two would allow you to see the protocol's level
candidate configuration? (Choose two.)
A. exit configuration-mode <enter>
show protocols
B. exit configuration-mode <enter>
show configuration protocols
C. top <enter>
show protocols
D. top show protocols
200-355 dumps Answer: C,D
QUESTION NO: 20
You are the top of the hierarchy in configuration mode.
How would you save your configuration to a file on the router?
A. save configuration <filename>
B. save config <filename>
C. save <filename>
D. save run <filename>
Answer: C
QUESTION NO: 21
You enter configuration mode with the configure command. You need to abort the
changes that you have made and start again with a fresh copy of the active configuration.
Which command should you use?
A. rollback 0
B. load active
C. reset config
D. clear candidate config
200-355 pdf Answer: A
QUESTION NO: 22
You have just issued the command commit confirmed and your network continues to be operational with no further changes required. You issue a commit and-quit. A short time later, users start complaining about network problems. Which commands (in order) need to be entered to resolve this issue?
A. >commit confirmed
B. >configure
#rollback 1
#commit
C. >configure
#commit confirmed and-quit
D. >configure
Answer: B
QUESTION NO: 23
Which method loads the configuration which was active before your last commit?
A. load replace last-active
B. load rollback 1
C. rollback 1
D. rollback last-active
200-355 vce Answer: C
QUESTION NO: 24
Which command would allow you to compare two files stored on your router?
A.user@host> file show filename1 compare filename2
B. user@host> file compare files filename1 filename2
C. user@host> compare files filename1 filename 2
D. user@host> compare filename1 filename2
Answer: B
QUESTION NO: 25
Which services must be enabled on a router to access JWEB?
A. web-management{
http;
B. remote-accessprofile{
http;
C. remote-accessprofile{
web-gui;
D. web-management{
web-gui;
200-355 exam Answer: A
QUESTION NO: 26
How can you reset your router or switch to factory defaults?
A. reset configuration
B. load factory-default
C. load override default
D. set default configuration
Answer: B
QUESTION NO: 27
After factory-defaults have been loaded, which two syslog files will be present in the
configuration?
A. system and chassisd
B. syslog-messages and NVRAM
C. messages and interactive-commands
D. authorization and events
200-355 dumps Answer: C
QUESTION NO: 28
Which three steps are considered part of the initial configuration? (Choose three.)
A. SNMP
B. hostname
C. root password
D. user password
E. management access interface
Answer: B,C,E
QUESTION NO: 29
What are two valid initial configuration methods supported on Juniper routers? (Choose
two)
A. CLI
B. J-Web
C. JUNOScope
D. PCMCIA flash card
200-355 pdf Answer: A,B

When it comes to the Cisco 200-355 dumps is of utmost importance. You do not want something that is outdated and you certainly do not want something that is not practical to use.  Exam information: https://www.pass4itsure.com/200-355.html
Related posts：
Some general links first: http://www.braindumpscity.com/2016-sep-newccna-wireless-200-355-pdf-download.html
More questions are available at: http://www.n10-006pdf.com/most-important-cisco-wireless-200-355-dumps.html
Read More Youtube: https://youtu.be/rHndBhwhzPw